Select The Right Tool Set
STEP 1 - Select your Base Tool Set
Consider renting or purchasing...
Each 2-Car Pro Driveway Kit includes:
(1) Pro Pak Kit (Go 22 ft. with up to 2" dia. pipe!):
- - 1” Compression Point and threadless Impact Cap;
- - 2" Compression Point and threadless Impact Cap;
- - 1" Plus Compression Point;
- - 3/4" and 1" PVC Pull Connector;
- - 3/4" and 1" NPT Pull Connector;
- - Extractor Ring;
- - Jack Hammer Adapter
- 22 ft. of shafts: qty (1) 4 ft. shaft and qty (3) 6 ft. shafts
- (1) Sled Guide
Each 2-Car Standard Driveway Kit includes:
(1) Standard Pak Kit (Go 18 ft. with up to 1" dia. pipe!):
- - 1" Compression Point and threadless Impact Cap;
- - 3/4" and 1" PVC Pull Connector;
- - Extractor Ring;
- 18 ft. of shafts: qty (3) 6 ft. shafts
Or Make Your Own Tool System Kit
4 ft. Quick Unit - (Residential length sidewalk) QK240
6 ft. Quick Unit - (Commercial length sidewalk) QK260
Each kit comes standard with:
- (1) 4 ft. or 6 ft. Quick Shaft ®
- (1) 1” Compression Point
- (1) 1” Impact Cap
STEP 2 - Select Nominal Pipe Size to Install
Note: This step determines if additional Points are required.
Nominal Pipe Size-
1” Compression Point - CP210
(Comes Standard w/ Kit)
1 3/4” O.D.
3/4”
1”
-
1” Plus Compression Point - CP211
2” O.D.
1 1/4”
1 1/2”
-
2” Compression Point - CP220
(Sold as Kit with 2” Impact Cap)
3” O.D.
2”
STEP 3 - Determine Total Length of Pipe Run
Use Extension Shafts on longer runs, like under driveways. Getting a good mix of extensions gives you future flexibility.
Extension shafts screw together:
-
6 ft. Extension Shaft - ES260
-
4 ft. Extension Shaft - ES240
-
2 ft Extension Shaft - ES220
Subtract the Quick unit length (4 ft or 6 ft) from the total distance of run to determine required “Extension Length.”
Divide this Extension Length by (6 ft or 4 ft or 2 ft) to determine how many extensions of each length are needed.
EXAMPLE:
Total Length of Pipe Run = 16 ft (2-car driveway)
Length of Quick Shaft Unit Selected Above = 4 ft.
- Extension Length required = (16 ft. - 4 ft.) = 12 ft.
- 12 ft. (divide symbol) 6 ft. = Qty (2) or
- 12 ft. (divide symbol) 4 ft. = Qty (3) or
- 12 ft. (divide symbol) 2 ft. = Qty (6)
STEP 4 - Select Accessories - Select Accessories
Useful additions to simplify your installation
Sled Guide - SG200
The sled guide holds the tool straight and at the right distance from the bottom of the trench too.
Jack Hammer Adapter - JH2001
Fits over our Threadless Impact Caps and accommodates most Jack Hammers.
Extractor Ring - EX201
The Extractor Ring screws in to the forged shaft end after the Impact Slip Cap is removed. We recommend you use the Extractor Ring with a 6' Pry Bar to remove the tool when pulling the pipe back after making the hole.
Pull Connectors:
Pull Connectors are used for pulling back through loose material (such as pea gravel) or if you simply desire to install a continuous length of pipe without joints in long run situations, typically 10 - 20 ft.
-
PVC 3/4” & 1” Combo - PC17P
Used to pullback 3/4” or 1” PVC pipe through the hole you have made. It utilizes self tapping buttress threads to attach to PVC pipe to the shaft.
-
NPT 3/4” & 1” Combo - PC10T
Used to pullback 3/4” or 1” NPT pipe through the hole you have made. You simply screw on the pipe and attach to the shaft. Also included but not shown is a 1" to 3/4" reducer.